The national benchmark
Angi reports a typical US range of $551–$1,382, an average of $964, and professional installation labor of $400–$1,200. HomeAdvisor reports $555–$1,380, an average of $967, and the same broad labor range.
The companies are related and their figures are very similar, so treat them as one consistent national benchmark—not two independent proofs of a Massachusetts price. Figures were reviewed in November 2026 and do not constitute a local quote.
A simple project near suitable capacity can differ sharply from a long outdoor run or one requiring service work.
Equipment versus installed cost
| Component | What to identify in the quote |
|---|---|
| Charger / EVSE | Model, maximum and configured output, connector, cable length, smart features |
| Dedicated circuit | Conductors, protection, disconnect or receptacle requirements |
| Professional labor | Installation, route, mounting, configuration and testing |
| Mounting and protection | Wall hardware, pedestal, weather exposure and physical protection |
| Permit and inspection | Application, fee and who schedules the inspection |
| Electrical upgrades | Panel, service or load-management work when required |
| Restoration | Wall, ceiling, pavement or landscaping work after the route is installed |
Angi places Level 2 equipment at $300 to more than $1,000 depending on features and gives a $700–$2,000 charger-plus-labor scenario. The broader installation ranges above and additional work below should not be added together blindly; check what each quoted figure already includes.
Level 1 versus Level 2 budget
Level 1 uses a 120V supply and may avoid a new charging circuit where a suitable existing setup is available. That does not make any convenient household receptacle automatically appropriate for sustained vehicle charging; the circuit and equipment still need to be suitable.
Level 2 uses 208–240V and generally involves a dedicated circuit. Its higher installation scope buys faster charging, but the selected output should match the vehicle, driving needs and calculated electrical capacity.
The EV charger installation guide explains how to choose between them before comparing prices.
Cable route and labor
Professional labor commonly starts with the route. A panel next to a garage wall can be straightforward; a detached garage, finished basement or distant driveway can require more labor and materials.
Give every estimator the same information:
- panel and proposed charger locations;
- approximate distance and finished surfaces along the route;
- indoor or outdoor mounting;
- vehicle connector and desired charging rate;
- any future second vehicle or charger.
A quote based only on “Level 2 installation” leaves the most location-sensitive work undefined.
Outdoor mounting and accessories
Published guides separately list weather protection, mounting hardware and pedestals. Angi cites $50–$150 for wall-mount accessories and $300 or more for a pedestal; its weather-protection examples range from a simple cover to a heavier enclosure.
Those accessory prices do not capture every outdoor electrical requirement. Equipment listing, conductor protection, mounting height, cable management and exposure to vehicles, snow and water must be designed for the location. Do not buy an indoor unit and assume a cover makes the installation suitable outdoors.
Panel upgrades and wiring are separate scenarios
Angi’s guide cites $500–$1,500 for additional wiring in some scenarios and $800–$2,000 for electrical upgrades. Its panel figure is a general example, not a complete Massachusetts service-upgrade estimate.
For a fuller panel scope, use the panel upgrade cost guide. But first ask whether a lower charger setting or compatible load management can meet driving needs without a service upgrade. A panel capacity evaluation should precede the assumption.
Permits and multi-family scope
Angi lists permit costs around $100–$200 in its national guide. Actual municipal fees and requirements vary. Worcester issues electrical permits and conducts associated inspections through Building & Zoning; Sutton uses an online permitting process.
A triple-decker or multi-unit project can also involve common-area permissions, shared service, metering and access control. Those are not “accessories.” They may define the project before the charger price is relevant. See the Worcester multi-family considerations for the questions to resolve.
Compare itemized estimates
Ask for equipment, configured amperage, circuit, route, mounting, permit, panel work and restoration as separate items. Keep incentives out of the base comparison until current official eligibility is verified.
Use the project planner to record the vehicle, parking and panel details. Local project resources are available for Worcester and Sutton.